Installing Slab French Doors In A Cased Opening The Easy Way – Part 1

I made a decision that I have to go forward and set up the French doorways to our bed room suite because the flooring is within the means of being torn up, and Felicity (our cat) has now been below the home at the least 3 times. The bed room the place the ground is at present being torn out (the teal door on the left within the picture beneath) does have a pocket door on it…

I ordered two of those slab 10-lite doorways from House Depot.

The rationale that I ordered slab doorways as an alternative of pre-hung French doorways is as a result of the doorway the place I need to set up these doorways has already been trimmed out. I’m turning this cased opening between the music room and the hallway into the doorway to our new bed room suite. Finally, the doorway into the toilet shall be closed up, and the toilet shall be accessible on the other wall of the toilet. However that’s for one more time. For now, I simply wanted to get these French doorways put in on this already trimmed out cased opening.

The cased opening is 46 inches extensive, so I ordered two 24-inch-wide doorways in order that they’d be facet sufficient to cowl the opening, however figuring out that they’d should be minimize down only a bit. And since I needed to do that the best manner doable, I bought non-mortise door hinges for the doorways. I purchased three hinges for every door. Non-mortise door hinges don’t require using a router or chisel to put in the door. You simply screw the hinges on to the door jamb and to the sting of the door with no mess or fuss. It’s tremendous simple! I did purchase longer screws, although. Since my doorways are type of heavy (and never hole core doorways), I didn’t need to use these little screws supplied with the hinges.

Beginning on the high of the door jamb, I measured down 6.5 inches, after which screwed the hinge in place in order that the highest of the hinge was on the pencil mark.

Subsequent, I measured up from the ground 7.5 inches and made a mark. I screwed the hinge on in order that the underside of the hinge was on the mark. And at last, I measured and marked the middle level between these two hinges and screwed the third hinge onto the door jamb in order that it was centered between the opposite two.

I repeated that course of on the opposite door jamb.

Subsequent, I used scrap lumber to shim the door up excessive sufficient in order that there was about 1/8 inch between the highest of the door and the highest jamb.

This was a bit difficult doing all of this on my own — holding the door in place, lining up the sting of the door with the hinge, and screwing the hinge into place. However with some persistence, I managed to get it screwed on. I began with the middle hinge simply because it was the best to do first. Had I began with the underside, I’d have wanted one other individual to assist me maintain the door in place, and had I began with the highest, I’d have needed to do all of that balancing act on a ladder, which might have been extremely irritating. So beginning with the middle hinge made extra sense. I didn’t make any marks earlier than screwing the door to the hinge. The marks you see there are simply from the steel of the hinge scraping in opposition to the door as I attempted to get the door in simply the appropriate place.

However as soon as the center hinge was connected, the remaining was very simple. I did the highest one subsequent, and it was very simple to line up and get it screwed on.

After which the underside one was additionally very simple. So it was actually simply the primary one which was a bit difficult.

And right here’s how that appeared as soon as all three had been connected. You possibly can see mild across the door with the sort of hinge, however that downside is solved as soon as the cease is connected.

Earlier than attaching the cease, I first needed to set up the second door. I put in this one a bit in a different way since I wanted the doorways to match precisely. As a substitute of beginning the set up of the second door with the center hinge, I as an alternative measured the location of the highest hinge on the primary door, and replicated that actual placement on the second door, predrilling the holes to make it so simple as doable as soon as I stepped up on the ladder, after which labored my manner down. As a result of I used to be working with pre-drilled holes, ranging from the highest and dealing down on the second door was truly fairly simple.

I made a decision to put in the doorways earlier than trimming the surplus width. I’m solely going to trim the surplus width off of the within edge on every door, so I’ll do this by eradicating the hinge pins to take away the doorways, utilizing my round noticed to trim the sting, after which rehanging the door by merely lining up the hinges and placing the pins again in.

I do know that simply trimming off the surplus with from the within edge on every door will make the stiles on every door completely different widths. And if the doorway solely had one door on it, I’d by no means think about doing that. However because it’s two doorways, they usually’ll be good mirror photographs of one another to keep up that steadiness, I believe it’ll be advantageous. Proper? You’ll have to influence me if you happen to disagree. 😀

To complete up the door trim, I wanted to put in cease across the edges. I began with the highest piece, which I minimize with my miter noticed after which connected utilizing 1.5-inch 16-gauge nails.

After which I connected the facet items of cease.

You possibly can see how the cease covers over that small hole from the non-mortise hinges.

After which I connected the cease on the opposite facet. And right here’s what the doorways appeared like after I stopped for the night.

Slicing the doorways down would be the most nerve wracking a part of the undertaking. I’m not trying ahead to that half, however I’m trying ahead to those doorways being utterly put in! As soon as they’re minimize down and put again into place, I’ll want to put in some ball catch closures on the highest jamb in order that the doorways will truly keep closed. Hopefully I can get the remaining completed at the moment and present you the completed French doorways tomorrow!